| No. | Partie # | Fabricant | Description | Fiche Technique |
|---|---|---|---|---|
|
|
|
ETC |
USB PD and other fast charging protocol power receiving chip |
|
|
|
|
Texas Instruments |
OCTAL BUFFERS/DRIVERS • Operate From 1.65 V to 3.6 V • Inputs Accept Voltages to 5.5 V • Max tpd of 5.9 ns at 3.3 V • Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C • Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25°C • Support Mixe |
|
|
|
|
Texas Instruments |
Octal Bus Transceivers •1 Operate From 1.65 V to 3.6 V • Inputs Accept Voltages to 5.5 V • Max tpd of 6.3 ns at 3.3 V • Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C • Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25°C • Support Mixe |
|
|
|
|
Texas Instruments |
OCTAL BUFFERS/DRIVERS • Operate From 1.65 V to 3.6 V • Inputs Accept Voltages to 5.5 V • Max tpd of 5.9 ns at 3.3 V • Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C • Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25°C • Support Mixe |
|
|
|
|
Texas Instruments |
Bus Transceiver •1 Available in the Texas Instruments NanoFree™ Package • VCC Isolation • 2-Rail Design • I/Os are 4.6 V Tolerant • Partial Power-Down-Mode Operation • Bus Hold on Data Inputs • Maximum Data Rates – 500 Mbps (1.8 V to 3.3 V) – 320 Mbps (< 1.8 V to 3. |
|
|
|
|
Texas Instruments |
OCTAL BUFFER/DRIVER separate output-enable (OE) inputs. When OE is low, the device passes data from the A inputs to the Y outputs. When OE is high, the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should b |
|
|
|
|
ETC |
Triode - Heptode |
|
|
|
|
ETC |
DC/DC CONVERTERS 5/ 12/ OR 28 VOLT INPUT • –55°C to 100°C • 4 to 6.5, 9 to 15, or 20 to 32 VDC input • Fully isolated • Output regulated from input side • 100 kHz typical switching frequency • Topology – Push-Pull DC/DC Converter • Up to 75% efficiency • No minimum load • Output capacitor s |
|
|
|
|
ETC |
DC/DC CONVERTERS 5/ 12/ OR 28 VOLT INPUT • –55°C to 100°C • 4 to 6.5, 9 to 15, or 20 to 32 VDC input • Fully isolated • Output regulated from input side • 100 kHz typical switching frequency • Topology – Push-Pull DC/DC Converter • Up to 75% efficiency • No minimum load • Output capacitor s |
|
|
|
|
ETC |
DC/DC CONVERTERS 5/ 12/ OR 28 VOLT INPUT • –55°C to 100°C • 4 to 6.5, 9 to 15, or 20 to 32 VDC input • Fully isolated • Output regulated from input side • 100 kHz typical switching frequency • Topology – Push-Pull DC/DC Converter • Up to 75% efficiency • No minimum load • Output capacitor s |
|
|
|
|
ETC |
DC/DC CONVERTERS 5/ 12/ OR 28 VOLT INPUT • –55°C to 100°C • 4 to 6.5, 9 to 15, or 20 to 32 VDC input • Fully isolated • Output regulated from input side • 100 kHz typical switching frequency • Topology – Push-Pull DC/DC Converter • Up to 75% efficiency • No minimum load • Output capacitor s |
|
|
|
|
ETC |
44 pin QFP socket/28 pin DIP 0.6 plug typical 11.6 maximum 13.2 maximum Pitch 0.8 mm Adapter Wiring The following chart shows the connections from the QFP device to the adapter’s DIP plug. DEVICE 39 40 41 42 43 44 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SIGNAL GND I/O 0 10K I/O 2 10K 1/ |
|
|
|
|
ETCTI |
OCTAL BUS TRANSCEIVER (Rev. G) |
|
|
|
|
ETCTI |
OCTAL BUFFER/DRIVER (Rev. F) |
|
|
|
|
Texas Instruments |
Octal Bus Transceivers •1 Operate From 1.65 V to 3.6 V • Inputs Accept Voltages to 5.5 V • Max tpd of 6.3 ns at 3.3 V • Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C • Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25°C • Support Mixe |
|
|
|
|
Texas Instruments |
24-Bit Dual-Supply Bus Transceiver • Control Inputs VIH/VIL Levels Are Referenced to VCCA Voltage • VCC Isolation Feature – If Either VCC Input Is at GND, All Outputs Are in the High-Impedance State • Overvoltage-Tolerant Inputs/Outputs Allow MixedVoltage-Mode Data Communications • Fu |
|
|
|
|
Texas Instruments |
20-BIT DUAL-SUPPLY BUS TRANSCEIVER − If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State D Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications D Fully Configurable Dual-Rail Design Allows Each Port to Operate Over the Full 1.2-V to 3. |
|
|
|
|
Texas Instruments |
OCTAL BUS TRANSCEIVER buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so the buses are effectivel |
|
|
|
|
Texas Instruments |
OCTAL BUS TRANSCEIVER • Qualification in Accordance With AEC-Q100 (1) • Qualified for Automotive Applications • Customer-Specific Configuration Control Can Be Supported Along With Major-Change Approval • ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds |
|