No. | Partie # | Fabricant | Description | Fiche Technique |
---|---|---|---|---|
|
|
Wuxi Youda electronics |
18W CAR RADIO POWER AMPLIFIER *Requires very few external components for Bridge Tied Load (BTL),Stereo or BTL application; *High output power, Fixed gain, Good ripple rejection; * Identical inputs (inverting and non-inverting),Low offset voltage at output (important for BTL); *Mu |
|
|
|
Wuxi Youda electronics |
STEREO POWER AMPLIFIER *Requires very few external components *High output power *Fixed gain *Good ripple rejection *Mute/stand-by switch *Load dump protection *AC and DC short-circuit-safe to ground and Vcc *Thermally protected *Reverse polarity safe *Capability to handle |
|
|
|
WuXi YouDa Electronics |
10W AUDIO AMPLIFIER *Operation supply voltage range: Vcc=8V~18V *High Power: Po=10W (Vcc=16.5V,RL=2Ω,f=1kHz,THD=10%) Po=6W (Vcc=16.5V,RL=4Ω,f=1kHz,THD=10%) *Low popping noise at power ON. BLOCK DIAGRAM 1 2 3 4 5 6 7 8 9 10 ABSOLUTE MAXIMUM RATINGS PARAMETER |
|
|
|
Wuxi Youda electronics |
30W Audio power amplifier 5k R6 200k YD1875 |
|
|
|
Wuxi Youda Electronics |
18W Hi-Fi Audio Amplifier *Very low external component required. *High Current output and high operating voltage. *Low harmonic and crossover distortion. *Built-in Over temperature protection. *Short circuit protection between all pins. *Safety Operating Area for output trans |
|
|
|
Wuxi Youda electronics |
4W audio power amplifier 3 0.1u 470u Vin 8 0.22u 2 0.1u + 470u 9 7 DC Volume Control 1 3.3Ω ( :,) :www.e-youda.com |
|
|
|
Wuxi Youda electronics |
6W STEREO CAR RADIO POWER AMPLIFIER *Requires very few external components for Bridge Tied Load (BTL) *Stereo or BTL application *High output power *Low offset voltage at output (important for BTL) *Fixed gain *Good ripple rejection *Mute/stand-by switch *Load dump protection *AC and D |
|
|
|
Wuxi Youda Electronics |
6W Stereo Amplifier *High output power; *High current capability; *AC short circuit protection; *Thermal overload protection. BLOCK DIAGRAM 3 FIL 5 8 vcc w w w t a .D 1 S a - + - GND 6 + e h U 4 t e 7 4 9 .c m o 2 WuXi YouDa Electronics Co., Ltd Add: E-3 |
|
|
|
Wuxi Youda Electronics |
0.72W Audio Power Amplifier *Very few external components (only three capacitors). *Low quiescent current. *High Voltage Gain: Gv=40dB. BLOCK DIAGRAM m o .c U 4 t e WuXi YouDa Electronics Co., Ltd e h Add: No.5 Xijin Road, National Hi-Tech Industrial Development Zone, Wuxi Ji |
|
|
|
Wuxi Youda Electronics |
22W Hi-Fi Audio Amplifier *High output power *High operating supply voltage (50V) *Single or split supply operations *Very low distortion *Short circuit protection (out to end) *Thermal shutdown YD1008 YD1008 BLOCK DIAGRAM w w w t a .D 1 S a + _ 2 3 e h 4 U 4 t e . |
|
|
|
Wuxi Youda electronics |
LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS *Low dropout voltage (1V typ) *2.85V Device performances are suitable for scsi-2 active termination *Output current up to 800mA *Fixed output voltage of :2.5V, 2.85V, 3.0V, 3.3V, 5.0V *Adjustable version availability (Vref=1.25V) *Internal current an |
|
|
|
Wuxi Youda electronics |
SINGLE-CHIP FM/AM RADIO-IC *Small number of peripheral components. *Low current consumption (Vcc=3V) For FM:ID=5.3mA (Typ.) For AM:ID=3.4mA (Typ.) *Built-in FM/AM select switch. *Built-in RF AGC, IF AGC circuit. *Tuning LED driver. *Large output of AF amplifier. Vcc=6V,EIAJ ou |
|
|
|
Wuxi Youda electronics |
SINGLE-CHIP FM/AM RADIO-IC *Small number of peripheral components. *Low current consumption (Vcc=3V) For FM:ID=5.3mA (Typ.) For AM:ID=3.4mA (Typ.) *Built-in FM/AM select switch. *Built-in RF AGC, IF AGC circuit. *Large output of AF amplifier. Vcc=6V,EIAJ output=500mW (Typ.) Wh |
|
|
|
Wuxi Youda electronics |
2W DUAL CHANNEL AUDIO POWER AMPLIFIER *Wide operating voltage (Vcc=3V to 16V); *Low quiescent current; *Low Harmonic distortion; *Large output power (Po=2W×2, maximum, VCC=12V, RL=8Ω, THD=10%); *Fine ripple rejection characteristic. BLOCK DIAGRAM 14 GND 13 12 11 10 9 Vcc 8 TAB NC 1 2 3 |
|
|
|
Wuxi Youda electronics |
6W STEREO POWER AMPLIFIER *Requires very few external components for Bridge Tied Load (BTL),Stereo or BTL application; *High output power, Fixed gain, Good ripple rejection; * Identical inputs (inverting and non-inverting),Low offset voltage at output (important for BTL); *Mu |
|
|
|
Wuxi Youda electronics |
FM/AM VILIM VODB THD S/N Vi=40dBμ、30% Vi=70dBμ、30% Vi=70dBμ、30% -3dB 、30% Vi=80dBμ、30% Vi=80dBμ、30% Vi=40dBμ 0.5 Icca V2 V4 V5 V6 V7 V8 V9 V10 V13 V14 V16 V17 V19 V20 0.5 1.6 1.6 0.6 0.6 1.9 1.7 1.7 1.1 1.1 1.1 1.9 1.8 YD1800 5.6 2.6 2.3 2.3 1.7 1.7 1.7 |
|