No. | Partie # | Fabricant | Description | Fiche Technique |
---|---|---|---|---|
|
|
Sanyo |
Power Amplifier • Built-in 2 channels (dual) enabling use in stereo and bridge amplifier applications. Dual : 6W×2 (typ.) Bridge : 19W (typ.) • Minimun number of external parts required. • Small pop noise at the time of power supply ON/OFF and good starting balance. |
|
|
|
Sanyo |
2-CHANNEL AF POWER AMPLIFIER |
|
|
|
Sanyo |
7W x 2ch Power Amplifier 150 3 -25 to +75 -40 to +150 Unit V W °C °C/W °C °C 42706 MS JK B8-7230 No.A0315-1/5 Operating Conditions at Ta = 25°C Parameter Recommended supply voltage Recommended load resistance Allowable operating voltage range Symbol VCC RL VCC op LA420 |
|
|
|
Sanyo |
6W Monaural Power Amplifier a built-in electronic volume control circuit and only requires a minimal number of external components and thus is optimal for use as the audio output power amplifier in TV sets. Functions • 6W monaural power amplifier (VCC = 20V, RL = 8Ω) • This de |
|
|
|
Sanyo |
Two- channel Audio Power Amplifier |
|
|
|
Sanyo |
20 W 2-channel BTL AF Power Amplifier on-chip protectors and standby switch. The LA4708 is also pin-compatible with the LA4705NA (car stereo-use 17 W two-channel power IC), and can be substituted for the LA4705NA for higher power. (When the board is shared, pins 1 and 9 must be left open |
|
|
|
Sanyo |
Two-Channel 16-W BTL General-Purpose Audio Power Amplifier • Wide operating supply voltage range (VCCop): 5.5 to 22 V (Certain conditions may apply.) • High ripple rejection ratio: 60 dB (typical) • Power: 16 W × 2 (VCC = 15 V/6Ω), 13 W × 2 (VCC = 12 V/4Ω), 6.5 W × 2 (VCC = 9 V/4Ω) • Built-in signal muting c |
|
|
|
Sanyo Semiconductor |
LA4135 |
|
|
|
Sanyo Electric |
15W × 2ch Power Amplifier Ratings 24 15 150 2 -25 to +75 -40 to +150 Unit V W °C °C/W °C °C 42606 MS JK B8-7286 No.A0316-1/5 LA42152 Operating Conditions at Ta=25°C Parameter Recommended supply voltage Recommended load resistance Allowable operating voltage range Symbol VC |
|
|
|
Sanyo |
5.3W 2-Channel AF Power Amplifier • Low idling current (20mA/2 channels) enabling prolonged battery life. • Less dependence of idling current on VCC. • High power (5.3W typ. ×2). • High ripple rejection (60dB at steady state). Since filters are arranged in 3 stages (including 1 stage |
|
|
|
Sanyo |
Two-channel Power Amplifier . No heat sink needed during 9 V operation . P = 2.9 W × 2 (V = 9 V, R = 3.2 Ω, THD = 10%). . Less quiescent current. (V = 9 V, 20 mA, typ). . Operating voltage range: V op = 4.2 to 16 V. O CC L CC CC SANYO : SIP14HZ Allowable power dissipation, P |
|
|
|
Sanyo Electric |
(LA4120 / LA4125) 2-Channel AF Power AMP for Radio Tape Recoder |
|
|
|
Sanyo |
Audio Power Amplifier commended supply voltage Recommended load resistance Operating supply voltage range Operating load resistance range Symbol Vcc RL Vcc Op Within maximum ratings Conditions Ratings 12 4 5.0 to 22 2.7 to 8 Unit V Ω V Ω Any and all SANYO products descri |
|
|
|
Sanyo Electric |
(LA4120 / LA4125) 2-Channel AF Power AMP for Radio Tape Recoder |
|
|
|
Sanyo |
0.5W AF Power Amplifier |
|
|
|
Sanyo |
2-CHANNEL AF POWER AMPLIFIER |
|
|
|
Sanyo |
Dual AF Power Amplifier . Two-channel (dual) or single-channel (BTL) operation . Requires only a few external components. . 0.65 W (typ) output power into two 4 Ω speakers . Wide power supply range: 3 to 15 V . 8-pin DIP (No heat sink needed) SANYO : DIP8 Specifications A |
|
|
|
Sanyo Semiconductor |
2.5 - 6 Volt / 2-Channel |
|
|
|
Sanyo Semiconductor |
(LA4200 / LA4201) 1.5 - 2.5 W AF |
|
|
|
Sanyo Semicon Device |
5W X 2ch Power Amplifier ol VCC RL VCC op Under conditions such that maximum ratings are not exceeded Conditions Ratings 9.5 8 7 to 14 Unit V Ω V Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", inte |
|