No. | Partie # | Fabricant | Description | Fiche Technique |
---|---|---|---|---|
|
|
ROHM |
17W+17W Class D Speaker Amplifier 1 Digital Audio Interface I2S format SDATA: 16 / 20 / 24bit LRCLK (fS): 32 kHz/ 44.1kHz / 48kHz BCLK: 64fS (fixed) MCLK: 256fS / 512fS Automatic Identification) Low supply current at RESET mode. Slew rate controller ; No need snubber circuit (V |
|
|
|
Rohm |
1.0A Current Limit High-Side Switch Built-in Low ON-Resistance (Typ 110mΩ) N-Channel MOSFET Over-Current Detection Thermal Shutdown Open-Drain Fault Flag Output Flag Output Delay Under-Voltage Lockout Soft-Start Circuit Output Discharge Function Reverse Curr |
|
|
|
ROHM |
20W+20W Class D Speaker Amplifier 1 Digital Audio Interface I2S format SDATA: 16 / 20 / 24bit LRCLK (fS): 32kHz / 44.1kH |
|
|
|
Rohm |
1.0A Current Limit High-Side Switch Built-in Low ON-Resistance (Typ 110mΩ) N-Channel MOSFET Over-Current Detection Thermal Shutdown Open-Drain Fault Flag Output Flag Output Delay Under-Voltage Lockout Soft-Start Circuit Output Discharge Function Reverse Curr |
|
|
|
ROHM |
9W+9W Analog Input Class D Speaker Amplifier Analog Differential Input Low Standby Current Output Feedback Circuitry Prevents Sound Quality Degradation Caused by Power Supply Voltage Fluctuation, Achieves Low Noise and Low Distortion, Eliminates the Need of Large Electrolytic-Capacitors f |
|
|
|
Rohm |
0.5A Current Limit High Side Switch Built-In Low ON-Resistance Nch MOSFET ( Typ=80mΩ ) Control Input Logic Active-Low: BD2045AFJ Active-High: BD2055AFJ Soft-Start Circuit Over-Current Protection Thermal Shutdown Under Volt |
|
|
|
Rohm |
2-Channel RGB Charge Pump LED Driver RGB LED driver (dual drivers) A slope control function is incorporated (allowing dual drivers to be controlled independently). Slope control can be implemented using the DC current. Two modes “continuous illumination mode” and “illumination single cy |
|
|
|
Rohm |
1.3A Current Limit High Side Switch ■ AEC-Q100 Qualified ■ Over Current Protection ■ Built-in Low ON-Resistance (Typ 110mΩ) N-Channel MOSFET ■ Thermal Shutdown ■ Open-Drain Fault Flag Output ■ Under-Voltage Lockout ■ Output Discharge Function ■ Soft-Start Circuit ■ Control In |
|
|
|
Rohm |
1.3A Current Limit High Side Switch ■ AEC-Q100 Qualified ■ Over Current Protection ■ Built-in Low ON-Resistance (Typ 110mΩ) N-Channel MOSFET ■ Thermal Shutdown ■ Open-Drain Fault Flag Output ■ Under-Voltage Lockout ■ Output Discharge Function ■ Soft-Start Circuit ■ Control In |
|
|
|
ROHM |
2A LDO Regulators Output current capability: 2A Output voltage: Variable, Fixed (1.5V / 1.8V / 2.5V / 3.0V / 3.3V / 5.0V / 8.0V / 9.0V / 12V / 15V / 16V) ±1% (±1.5%:BD15/18/25FD0W) High output voltage accuracy (Ta=25°C) Low saturation with PDMOS output Built |
|
|
|
ROHM |
0.3A Current Limit High-Side Switch AEC-Q100 Qualified(Note1) Over Current Threshold: 0.3A Built-in Low ON-Resistance (Typ 120mΩ) N-Channel MOSFET Reverse Current Protection when Power Switch Off Thermal Shutdown Under-Voltage Lockout Open-Drain Error Flag Output Output |
|
|
|
Rohm |
0.75A Current Limit High-Side Switch Built-in Low ON-Resistance (Typ 110mΩ) N-Channel MOSFET Over-Current Detection Thermal Shutdown Open-Drain Fault Flag Output Flag Output Delay Under-Voltage Lockout Soft-Start Circuit Output Discharge Function Reverse Current Pro |
|
|
|
Rohm |
0.75A Current Limit High-Side Switch Built-in Low ON-Resistance (Typ 110mΩ) N-Channel MOSFET Over-Current Detection Thermal Shutdown Open-Drain Fault Flag Output Flag Output Delay Under-Voltage Lockout Soft-Start Circuit Output Discharge Function Reverse Current Pro |
|
|
|
ROHM |
Filter-Less Class-D Monaural Speaker Amplifier High output power 2.5W typ.(VDD=5V, RL=4Ω, THD+N=10%, BTL) Very small package 9-Pin WL-CSP Gain selectable by external resistor LC Filter less Protection circuitry (Short protection, Thermal shutdown, Under voltage lockout) Analogue diffe |
|
|
|
ROHM |
24ch Constant Current LED Driver AEC-Q100 Qualified (Note 1) 2-Line Serial Control + Enable Signal VQFN48 Package 24 channel constant current LED driver (max 50mA / channel) Independent PWM control for each channel 6 bit current DAC for RGB Protection features Equipp |
|
|
|
ROHM |
Dot Matrix LED Display Driver 1) LED Matrix driver (7x17) ・It has 7-channel PMOS SWs and 17-channel current drivers with 1/7 timing driven sequentially. ・Put ON/OFF(for every dot). ・The current drivers can drive 0-20.00mA current with 16 step(for every dot). ・64 steps of the lumi |
|
|
|
Rohm |
Controller ■ Long time support a product for Industrial applications. ■ Built-in charge pump ■ Built-in discharge circuit for output charge ■ Soft start circuit ■ Built-in comparator with hysteresis function at control input terminal ■ Possible to drive N-chann |
|
|
|
Rohm |
System LED Drivers 1) RGB LED driver (dual drivers) - A slope control function is incorporated (allowing dual drivers to be controlled independently). - Slope control can be implemented using the DC current. - Two modes “continuous illumination mode” and “illumination |
|
|
|
Rohm |
2.4A Current Limit High Side Switch AEC-Q100 Qualified(Note 1) Built-in Dual Low ON-Resistance N-channel MOSFET(Typ 80mΩ) Control Input Logic Active-High : BD2068FJ-M Active-Low: Soft-Start Circuit BD2069FJ-M Over Current Detection Thermal Shutdown Under-Volta |
|
|
|
Rohm |
1ch Adjustable Current Limit High-Side Switch AEC-Q100 Qualified Adjustable Current Limit Threshold: 200mA to 1.7A Built-in Low On-Resistance (Typ 100mΩ) N-channel MOSFET Built-in Soft-Start Circuit Output Discharge Function Open-Drain Fault Flag Output Thermal Shutdown Under-Vol |
|