| No. | Partie # | Fabricant | Description | Fiche Technique |
|---|---|---|---|---|
|
|
|
Sanyo Semiconductor Corporation |
1-Channel Class AB Audio Power Amplifier • Series of pin compatible power amplifiers ranging from 45W to 180W (10%/1kHz) devices. The same printed circuit board can be used depending on the output power grade. • Miniature packages — 30W to 40W (THD=0.4%, f=20Hz to 20kHz); 44.0mm × 25.6mm × |
|
|
|
|
Sanyo Semiconductor Corporation |
af Power Amplifier • Series of pin compatible power amplifiers ranging from 20 W × 3 channels to 60 W × 3 channels (10%/1 kHz) devices. The same printed circuit board can be used depending on the output power grade. • The pin arrangement is compatible with that of the |
|
|
|
|
Sanyo Semiconductor Corporation |
Three-Channel Class AB Audio Power Amplifier • Series of pin compatible power amplifiers ranging from 20 W × 3 channels to 60 W × 3 channels (10%/1 kHz) devices. The same printed circuit board can be used depending on the output power grade. • The pin arrangement is compatible with that of the |
|
|
|
|
Sanyo Semiconductor |
(STK4xxx) Integrated circuit |
|
|
|
|
Sanyo Semiconductor Corporation |
Power AMP |
|
|
|
|
Sanyo Semiconductor Corporation |
One-Channel Class AB Audio Power Amplifier IC 5.6 Package Dimensions unit: mm 4201-SIP13 [STK404-130] 59.2 52.0 • Series of pin compatible power amplifiers ranging from 45 W to 180 W (10%/1 kHz) devices. The same printed circuit board can be used depending on the output power grade. • Miniatu |
|
|
|
|
Sanyo Semiconductor |
AF Power Amplifier • Pin compatible IC series that covers power ratings from 50 W × 2 channels to 180 W × 2 channels at 0.7 or 0.8% THD, 20 Hz to 20 kHz. This allows the use of a common PCB for all output classes. • The pin arrangement is also unified with that of the |
|
|
|
|
Sanyo Semiconductor |
AF Power Amplifier • Pin compatible IC series that covers power ratings from 50 W × 2 channels to 180 W × 2 channels at 0.7 or 0.8% THD, 20 Hz to 20 kHz. This allows the use of a common PCB for all output classes. • The pin arrangement is also unified with that of the |
|
|
|
|
ON Semiconductor |
2-phase Stepper Motor Driver Built-in overcurrent detection function, overheat detection function (output current OFF). FAULT1 signal (active low) is output when overcurrent or overheat is detected. The FAULT2 signal is used to output the result of activation of protection |
|
|
|
|
ON Semiconductor |
2-phase Stepping Motor Driver • The motor speed can be controlled by the frequency of an external clock signal. • 2-phase excitation or 1-2 phase excitation is selected according to switching the state of the MODE pin (low or high). • The phase is maintained even if the excitatio |
|
|
|
|
ON Semiconductor |
2-phase Stepping Motor Driver • The motor speed can be controlled by the frequency of an external clock signal. • 2-phase excitation or 1-2 phase excitation is selected according to switching the state of the MODE1 pin (low or high). • The excitation mode is set at the rising edg |
|
|
|
|
ON Semiconductor |
2-phase Stepper Motor Driver Built-in overcurrent detection function, overheat detection function (output current OFF). FAULT signal (active low) is output when overcurrent or overheat is detected. Built-in power on reset function. The motor speed is controlled by the |
|
|
|
|
Cypress Semiconductor |
64 Kbit (8 K x 8) AutoStore nvSRAM ■ 25 ns, 35 ns, and 45 ns access times ■ Hands off automatic STORE on power-down with external 68 µF capacitor ■ STORE to QuantumTrap nonvolatile elements is initiated by software, hardware, or AutoStore on power-down ■ RECALL to SRAM initiated by so |
|
|
|
|
Cypress Semiconductor |
32 K x 8 AutoStore nvSRAM ■ 25 ns, 35 ns, and 45 ns read access and R/W cycle time ■ Unlimited read/write endurance ■ Automatic nonvolatile STORE on power loss ■ Nonvolatile STORE under hardware or software control ■ Automatic RECALL to SRAM on power up ■ Unlimited RECALL cyc |
|
|
|
|
ON Semiconductor |
2-in-1 PFC and Inverter Intelligent Power Module Simple thermal design with PFC and inverter stage in one package. PFC operating |
|
|
|
|
Sanyo Semiconductor |
AF Power Amplifier • Pin compatible IC series that covers power ratings from 50 W × 2 channels to 180 W × 2 channels at 0.7 or 0.8% THD, 20 Hz to 20 kHz. This allows the use of a common PCB for all output classes. • The pin arrangement is also unified with that of the |
|
|
|
|
Sanyo Semiconductor |
AF Power Amplifier • Pin compatible IC series that covers power ratings from 50 W × 2 channels to 180 W × 2 channels at 0.7 or 0.8% THD, 20 Hz to 20 kHz. This allows the use of a common PCB for all output classes. • The pin arrangement is also unified with that of the |
|
|
|
|
Sanyo Semiconductor |
(STK4xxx) Integrated circuit |
|
|
|
|
ON Semiconductor |
2-phase Stepper Motor Driver Built-in overcurrent detection function, overheat detection function (output current OFF). FAULT1 signal (active low) is output when overcurrent or overheat is detected. The FAULT2 signal is used to output the result of activation of protection |
|
|
|
|
ON Semiconductor |
2-phase Stepping Motor Driver • Built-in overcurrent detection function (output current OFF). • Built-in overheat detection function (output current OFF). • If either over-current or overheat detection function is activated, the FAULT1 signal (active low) is output. The FAULT2 si |
|