No. | Partie # | Fabricant | Description | Fiche Technique |
---|---|---|---|---|
|
|
NXP |
Signal Souces Switch |
|
|
|
NXP |
2 x 7 W stereo Bridge Tied Load BTL audio amplifier s s s s s s s s s Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Pr |
|
|
|
NXP |
CONTROL CIRCUIT FOR SMPS Be sure to visit ChipDocs site for more information http://www.chipdocs.com Be sure to visit ChipDocs site for more information http://www.chipdocs.com |
|
|
|
NXP |
Multiple voltage regulator s Three enable pin controlled standby regulators: x REG1: 5 V / 600 mA controlled by the EN1 input x REG2: 3.3 V / 200 mA controlled by the EN2/3 input x REG3: 1.9 V / 150 mA controlled by the EN2/3 input s Four mode pin controlled switched regulator |
|
|
|
NXP |
Gating / Frequency Divider |
|
|
|
NXP |
26 W BTL and 2 x 13 W SE power amplifiers • Requires very few external components • High output power • Low output offset voltage (BTL channel) • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature detection) • Good ripple rejection • Mode select switch (operating, mu |
|
|
|
NXP |
Universal HiFi audio processor for TV • Multi-source selector switches six AF inputs (three stereo sources or six mono sources) • Each of the input signals can be switched to each of the outputs (crossbar switch) • Outputs for loudspeaker channel, headphone channel and peri-TV connector |
|
|
|
NXP |
Triple video output amplifier • Typical bandwidth of 5.5 MHz for an output signal of 60 V (p-p) • High slew rate of 900 V/µs • No external components required • Very simple application • Single supply voltage of 200 V • Internal reference voltage of 2.5 V • Fixed gain of 50 • Bla |
|
|
|
NXP |
4 x 40 W BTL quad car radio power amplifier • Requires very few external components • High output power • Low output offset voltage • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature pre-warning) • Good ripple rejection • Mode select switch (operating, mute and stand |
|
|
|
NXP |
2 to 6 W audio power amplifier are: • single in-line (SIL) construction for easy mounting • separated preamplifier and power amplifier • high output power • thermal protection • high input impedance • low current drain • limited noise behaviour at radio frequencies QUICK REFERENCE |
|
|
|
NXP |
BTSC-stereo/SAP/DBX decoder and DBX expander • DBX decoder, MPX decoder and SAP decoder on chip • Extensive switching possibilities for the AF outputs and the extra headphone output • Stereo and SAP signal available simultaneously • Reliable stereo/SAP identification by means of the noise detec |
|
|
|
NXP |
30 Msps analog-to-digital interface for CCD cameras • Clamp and Track/Hold (CTH) circuit with adjustable bandwidth, Programmable Gain Amplifier (PGA), 12-bit Analog-to-Digital Converter (ADC) and reference regulator • Fully programmable via a 3-wire serial interface • Sampling frequency up to 30 MHz • |
|
|
|
NXP |
DVB-T channel receiver • 2 and 8 kbytes Coded Orthogonal Frequency Division Multiplexer (COFDM) demodulator (fully DVB-T compliant: ETSI 300-744) • All modes supported, including hierarchical modes • Fully automatic transmission parameters detection (including Fast Fourier |
|
|
|
NXP |
12-bit high-speed Analog-to-Digital Converter ADC • 12-bit resolution • Sampling rate up to 55 MHz • −3 dB bandwidth of 190 MHz • 5 V power supplies • Binary or twos-complement CMOS outputs • In-range CMOS-compatible output • TLL-CMOS compatible static digital inputs • 3 to 5 V CMOS-compatible digit |
|
|
|
NXP |
10-bit high-speed low-power ADC with internal reference regulator • 10-bit resolution (binary or gray code) • Sampling rate up to 40 MHz (/4 version) Sampling rate up to 80 MHz (/8 version) • DC sampling allowed • One clock cycle conversion only • High signal-to-noise ratio over a large analog input frequency range |
|
|
|
NXP |
Triple 10-bit video Digital-to-Analog Converter DAC • 10-bit resolution • Sampling rate up to: – 50 MHz for normal mode; RL = 37.5 Ω – 35 MHz for LOW power mode; RL = 150 Ω • Internal current reference • Current reference selector for: – normal mode, RL = 37.5 Ω (typ.) – low-power mode, RL = 150 Ω (ty |
|
|
|
NXP |
Class AB stereo headphone driver and benefits Wide temperature range No switch ON/OFF clicks Excellent power supply ripple rejection Low power consumption Short-circuit resistant High performance High signal-to-noise ratio High slew rate Low distortion Large outp |
|
|
|
NXP |
Spatial/ stereo and pseudo-stereo sound circuit • Three switched functions: – spatial (widened stereo image) – stereo – pseudo-stereo (artificial stereo from a mono source) • Offset compensated operational amplifiers to reduce switch noise • LED driver outputs to facilitate indication of selected |
|
|
|
NXP |
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors Available in all ICs: • Vision IF amplifier with high sensitivity and good figures for differential phase and gain • PLL demodulator for the IF signal • Alignment-free sound demodulator • Flexible source selection with a CVBS input for the internal s |
|
|
|
NXP |
10-bit high-speed analog-to-digital converter • 10-bit resolution • Sampling rate up to 40 MHz • Total Harmonic Distortion (THD): −65 dB at 4.43 MHz full-scale and a 40 MHz clock frequency • High signal-to-noise ratio over a large analog input frequency range (8.8 effective bits at 10 MHz full-s |
|