| No. | Partie # | Fabricant | Description | Fiche Technique |
|---|---|---|---|---|
|
|
|
Freescale Semiconductor |
Multifunctional Ignition and Injector Driver • Designed to operate over the range of ~4.7 V ≤ VPWR ≤ 36 V • Fuel Injector driver - Current Limit - 4.0 A Typical • Ignition pre-driver can drive IGBT or Darlington bipolar junction EK Pb-FREE SUFFIX 98ASA10556D 32 Pin SOICW EP transistors • Ig |
|
|
|
|
Freescale Semiconductor |
One Cylinder Small Engine Controller |
|
|
|
|
Freescale Semiconductor |
One Cylinder Small Engine Control IC |
|
|
|
|
Freescale Semiconductor |
Single Wire CAN Transceiver • Waveshaping for low Electromagnetic Interference (EMI) • Detects and automatically handles loss of ground • Worst-case Sleep mode current of only 60 μA • Current limit prevents damage due to bus shorts • Built-in thermal shutdown on bus output • Pr |
|
|
|
|
Freescale Semiconductor |
Two cylinder small engine controller |
|
|
|
|
Freescale Semiconductor |
Automotive Engine Controller are enabled such as spark duration, dwell time, and ignition coil current sense. When configured as a general purpose gate pre-driver (GPGD), the 33810 provides external MOSFETs with short-circuit protection, inductive flyback protection and diagnost |
|
|
|
|
Freescale Semiconductor |
Configurable Octal Serial Switch include very low standby currents, cascade fault reporting, internal + 45 V clamp voltage for low-side configuration, - 20 V high-side configuration, output-specific diagnostics, and independent overtemperature protection. Features • Designed to Oper |
|
|
|
|
Freescale Semiconductor |
Quad Low-side Driver • RDSON of 250mΩ per Output at 25°C • Supplied from the main 5V VCC • Input CMOS Compatible • Diagnostic through SPI • Nominal Current of 2A per Output • Current Limitation at 3A with Automatic Turn Off • Output Internally Clamped at 50V typ for Indu |
|
|
|
|
Freescale Semiconductor |
System Basis Chip • Dual Low Drop Voltage Regulators, with Respectively 100 mA and 200 mA Current Capabilities, Current Limitation, and Over Temperature Detection with Pre-warning • 5.0 V Output Voltage for V1 Regulator • Three Operational Modes (Normal, Stand-by, and |
|
|
|
|
Freescale Semiconductor |
H-Bridge Gate Driver IC • VCC operating voltage range from 5.5 V up to 55 V • VCC2 operating voltage range from 5.5 V up to 28 V |
|
|
|
|
Freescale Semiconductor |
Programmable H-Bridge Power IC • Drives Inductive Loads in a Full H-Bridge Configuration VW SUFFIX (Pb-FREE) • Current Mirror Output Signal (Gain Selectable via External 98ASH70693A Resistor) 30-PIN HSOP • Short Circuit Current Limiting • Thermal Shutdown (Outputs Latched Off Unti |
|
|
|
|
Freescale Semiconductor |
Solenoid Monitor along with cost effective packaging, make the 33811 ideal for powertrain solenoid monitoring applications. Features • Typical operating voltage range, 10.5 < VPWR < 15.5 volts • Interfaces to 3.3 and 5 volt microprocessors via SPI protocol • Reset p |
|
|
|
|
Freescale Semiconductor |
Engine Control Integrated Circuit include: Low power Sleep Mode, Heated Exhaust Gas Oxygen (HEGO) sensor diagnostics, output control via serial and/or parallel inputs, PWM capability, and programmable current output with dithering. These features, along with cost effective packaging, |
|
|
|
|
Freescale Semiconductor |
System Basis Chip • VDD1: 5.0 V low drop voltage regulator, current limitation, overtemperature detection, monitoring and reset function with total current capability 200 mA • V2: tracking function of VDD1 regulator; control circuitry for external bipolar ballast tran |
|
|
|
|
Freescale Semiconductor |
Quad High-Side Switch • Quad 35 mΩ High-Side Switches (at 25°C) • Operating Voltage Range of 6.0 V to 27 V with Standby Current < 5.0 µA • SPI Control of Overcurrent Limit, Overcurrent Fault Blanking Time, Output OFF Open Load Detection, Output ON / OFF Control, Watchdog |
|
|
|
|
Freescale Semiconductor |
Configurable Octal Serial Switch include very low standby currents, cascade fault reporting, internal + 45 V clamp voltage for low-side configuration, - 20 V high-side configuration, output-specific diagnostics, and independent overtemperature protection. Features • Designed to Oper |
|
|
|
|
Freescale Semiconductor |
Configurable Octal Serial Switch include very low standby currents, “cascadable” fault reporting, internal 40 V output clamping for low-side configurations, internal -20 V output clamping for high-side configurations, output-specific diagnostics, and independent shutdown of outputs. |
|
|
|
|
Freescale Semiconductor |
System Basis Chip • VDD1: 5.0 V low drop voltage regulator, current limitation, overtemperature detection, monitoring and reset function with total current capability 200 mA • V2: tracking function of VDD1 regulator; control circuitry for external bipolar ballast tran |
|
|
|
|
Freescale Semiconductor |
Configurable Octal Serial Switch include very low standby currents, “cascadable” fault reporting, internal 40 V output clamping for low-side configurations, internal -20 V output clamping for high-side configurations, output-specific diagnostics, and independent shutdown of outputs. |
|
|
|
|
Freescale Semiconductor |
Six-Output Low-Side Switch including low standby current, fault status reporting, internal 52 V clamp on each output, output specific diagnostics, and protective shutdown. Additionally, it has a mode select pin affording a dual means of input control. Features • Outputs clamp |
|