| No. | Partie # | Fabricant | Description | Fiche Technique |
|---|---|---|---|---|
|
|
|
Texas Instruments |
1- to 4-Cell Hybrid Power Boost Mode Battery Charge Controller •1 Industrial Innovative Charge Controller With Hybrid Power Boost Mode – Adapter and Battery Provides Power to System Together for Intel® CPU Turbo Mode – Ultra-Fast Transient Response of 150 µs to Enter Boost Mode – Hybrid Power Boost Mode from 4.5 |
|
|
|
|
Texas Instruments |
BCD-TO-SEVEN-SEGMENT DECODERS/DRIVERS , ’LS49 BCD-TO-SEVEN-SEGMENT DECODERS/DRIVERS SDLS111 – MARCH 1974 – REVISED MARCH 1988 •4 POST OFFICE BOX 655303 DALLAS, TEXAS 75265 SN5446A, ’47A, ’48, SN54LS47, ’LS48, ’LS49 SN7446A, ’47A, ’48, SN74LS47, ’LS48, ’LS49 BCD-TO-SEVEN-SEGMENT DECODERS |
|
|
|
|
Texas Instruments |
Dual-Channel Gate Driver • Universal: dual low-side, dual high-side or halfbridge driver • Operating temperature range –40 to +125°C • Switching parameters: – 19-ns typical propagation delay – 10-ns minimum pulse width – 5-ns maximum delay matching – 6-ns maximum pulse-width |
|
|
|
|
Texas Instruments |
Octal Buffer/Driver • Operates From 1.65 V to 3.6 V • Inputs Accept Voltages to 5.5 V • Specified From –40°C to +85°C and –40°C to +125°C • Maximum tpd of 5.9 ns at 3.3 V • Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 3.3 V, TA = 25°C • Typical VOHV (Output VOH |
|
|
|
|
Texas Instruments |
Dual High-Speed MOSFET Drivers d TPS2813 drivers include a regulator to allow operation with supply inputs between 14 V and 40 V. The regulator output can power other circuitry, provided power dissipation does 1IN1 1IN2 2IN1 2IN2 1 2 3 4 8 GND 7 1OUT 6 VCC 5 2OUT TPS2815 . . . |
|
|
|
|
Texas Instruments |
Hex Schmitt-Trigger Inverters • Buffered inputs • Wide operating voltage range: 2 V to 6 V • Wide operating temperature range: -40°C to +85°C • Supports fanout up to 10 LSTTL loads • Significant power reduction compared to LSTTL logic ICs 2 Applications • Synchronize invterted cl |
|
|
|
|
Texas Instruments |
High-Speed CMOS Logic Octal Buffer/Line Drivers • HC/HCT240 Inverting • HC/HCT241 Non-inverting • HC/HCT244 Non-inverting • Typical propagation delay = 8ns at VCC = 5 V, CL = 15 pF, TA = 25℃ for HC240 • Three-state outputs • Buffered inputs • High-current bus driver outputs • Fanout (over temperat |
|
|
|
|
Texas Instruments |
16- and 32-Bit RISC Flash Microcontroller 1 • High-Performance Automotive-Grade Microcontroller for Safety-Critical Applications – Dual CPUs Running in Lockstep – ECC on Flash and RAM Interfaces – Built-In Self-Test (BIST) for CPU and On-chip RAMs – Error Signaling Module With Error Pin – Vo |
|
|
|
|
Texas Instruments |
Dot/Bar Display Driver 1 •2 3 dB/step, 30 dB Range • Drives LEDs, LCDs, or Vacuum Fluorescents • Bar or Dot Display Mode Externally Selectable by User • Expandable to Displays of 90 dB • Internal Voltage Reference from 1.2V to 12V • Operates with Single Supply of 3V to 25V |
|
|
|
|
Texas Instruments |
WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE-SUPPLY OPERATIONAL AMPLIFIER 1 •23 Qualified for Automotive Applications • Wide Bandwidth . . . 10 MHz • High-Output Drive – IOH . . . 57 mA at VDD – 1.5 V – IOL . . . 55 mA at 0.5 V • High Slew Rate – SR+ . . . 16 V/µs – SR – . . . 19 V/µs • Wide Supply Range . . . 4.5 V to 16 V |
|
|
|
|
Texas Instruments |
High-Speed CMOS Logic Octal Buffer/Line Drivers • HC/HCT240 Inverting • HC/HCT241 Non-inverting • HC/HCT244 Non-inverting • Typical propagation delay = 8ns at VCC = 5 V, CL = 15 pF, TA = 25℃ for HC240 • Three-state outputs • Buffered inputs • High-current bus driver outputs • Fanout (over temperat |
|
|
|
|
Texas Instruments |
Dual H-Bridge Motor Driver •1 Dual-H-Bridge Current-Control Motor Driver – Can Drive Two DC Motors or One Stepper Motor – Low MOSFET ON-Resistance: HS + LS 360 mΩ • Output Current (at VM = 5 V, 25°C) – 1.5-A RMS, 2-A Peak per H-Bridge in PWP and RTY Package Options – 500-mA RM |
|
|
|
|
Texas Instruments |
16- and 32-Bit RISC Flash Microcontroller 1 • High-Performance Microcontroller for SafetyCritical Applications – Dual CPUs Running in Lockstep – ECC on Flash and RAM Interfaces – Built-In Self-Test for CPU and On-Chip RAMs – Error Signaling Module With Error Pin – Voltage and Clock Monitorin |
|
|
|
|
Texas Instruments |
3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver •1 ESD Protection for RS-232 Bus Pins – ±15 kV (HBM) – ±8 kV (IEC61000-4-2, Contact Discharge) – ±15 kV (IEC61000-4-2, Air-Gap Discharge) • Meets or Exceeds the Requirements of TIA/EIA232-F and ITU V.28 Standards • Operates With 3-V to 5.5-V VCC Supp |
|
|
|
|
Texas Instruments |
Dual 4-A High Speed Low-Side MOSFET Drivers •1 Industry-Standard Pin-Out • Enable Functions for Each Driver • High Current Drive Capability of ±4 A • Unique BiPolar and CMOS True Drive Output Stage Provides High Current at MOSFET Miller Thresholds • TTL/CMOS Compatible Inputs Independent of Su |
|
|
|
|
Texas Instruments |
OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. The devices are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. On the posit |
|
|
|
|
Texas Instruments |
High-Speed CMOS Logic Octal Buffer/Line Drivers • HC/HCT240 Inverting • HC/HCT241 Non-inverting • HC/HCT244 Non-inverting • Typical propagation delay = 8ns at VCC = 5 V, CL = 15 pF, TA = 25℃ for HC240 • Three-state outputs • Buffered inputs • High-current bus driver outputs • Fanout (over temperat |
|
|
|
|
Texas Instruments |
Priority Encoder priority decoding of the inputs to ensure that only the highest-order data line is encoded. The ’147 and ’LS147 devices encode nine data lines to four-line (8-4-2-1) BCD. The implied decimal zero condition requires no input condition, as zero is enco |
|
|
|
|
Texas Instruments |
Polyphase Metering SoCs 1 • Accuracy < 0.1% Over 2000:1 Dynamic Range for Phase Current • Meets or Exceeds ANSI C12.20 and IEC 62053 Standards • Support for Multiple Sensors Such as Current Transformers, Rogowski Coils, or Shunts • Power Measurement for up to Three Phases P |
|
|
|
|
Texas Instruments |
ADVANCED UNIVERSAL SERIAL BUS TRANSCEIVER 1 • Complies With Universal Serial Bus Specification Rev. 2.0 (USB 2.0) • Transmits and Receives Serial Data at Both Full-Speed (12-Mbit/s) and Low-Speed (1.5-Mbit/s) Data Rates • Integrated Bypassable 5-V to 3.3-V Voltage Regulator for Powering Via |
|