| No. | Partie # | Fabricant | Description | Fiche Technique |
|---|---|---|---|---|
|
|
|
Texas Instruments |
Modular Current Sharing Controller 1 •2 Average Program Current Share Method • Single-wire Star Link Current Share Bus • No Precision External Resistors Necessary • 3V to 15V Bias Voltage Range • Adaptable for High or Low Side Current Sensing • Flexible Architecture Allows 4 Modes of |
|
|
|
|
Texas Instruments |
Buck Regulator •1 Wide 7.5- to 100-V Input Range • Integrated 300-mA High-Side and Low-Side Switches • No Schottky Required • Constant On-time Control • No Loop Compensation Required • Ultra-Fast Transient Response • Nearly Constant Operating Frequency • Intelligen |
|
|
|
|
Texas Instruments |
PWM Controller 1 •2 105V / 2A Half-Bridge Gate Drivers • Synchronous Rectifier Control Outputs with Programmable Delays • Synchronous Rectifiers Turned Off in Shutdown Modes. • Reduced Deadtime Between High and Low Side Drive for Higher Maximum Duty Cycle. • High V |
|
|
|
|
Texas Instruments |
High Voltage Dual Interleaved Controller 1 •2 Two Independent PWM Current Mode Controllers • Integrated High Voltage Startup Regulator • Compound 2.5A Main Output Gate Drivers • Single Resistor Oscillator Setting to 2 MHz • Synchronizable Oscillator • Active Clamp Gate Driver for P-Channel |
|
|
|
|
Texas Instruments |
100-V Push-Pull Current Mode PWM Controller •1 Internal High-Voltage Start-Up Regulator • Single Resistor Oscillator Setting • Synchronizable • Error Amplifier • Precision Reference • Adjustable Softstart • Dual Mode Overcurrent Protection • Slope Compensation • Direct Optocoupler Interface • |
|
|
|
|
Texas Instruments |
100V Power Over Ethernet PD Interface and PWM Controller 1 •2 PD Interface – Fully Compliant IEEE 802.3af PD Interface – Versatile Auxiliary Power Options – 9V Minimum Auxiliary Power Operating Range – 100V Maximum Input Voltage Rating – Programmable DC Current Limit Up To 800mA – 100V, 0.7Ω Hot Swap MOSFE |
|
|
|
|
ETC |
GRAPHICS PROCESSING IC PROVIDING HIGH QUALITY IMAGES FOR LCD MONITORS |
|
|
|
|
ETC |
Digit Backlit LCD Module put leakage current (Vin = 0V) Min. Typ. 0.05 3 100 9 150 5 30 1 Max. 0.1 ±1 50 14 60 10 0 7.5 % (±1 count) count sample/sec °C ppm/°C V µA V mA pA Unit NOTE Ensure link 10 is cut if fitting Ra. * To ensure maximum accuracy, re-calibrate peri |
|
|
|
|
Texas Instruments |
High-Voltage Dual Interleaved Controller •1 Two Independent PWM Current Mode Controllers • Integrated High-Voltage Startup Regulator • Compound 2.5-A Main Output Gate Drivers • Single Resistor Oscillator Setting to 2 MHz • Synchronizable Oscillator • Programmable Maximum Duty Cycle • Maximu |
|
|
|
|
Texas Instruments |
High-Side Protection Controller •1 Available in Automotive Grade / AEC Q-100 • Wide operating input voltage range: 5.5 V to 65 V • Functional safety capable – Documentation available to aid functional safety system design • Less than 15-µA quiescent current in disabled mode • Contr |
|
|
|
|
Texas Instruments |
Hotswap Controller •1 10- to 80-V Operation • 100-V Continuous Absolute Max • 26 mV or 50 mV ILIM Threshold (±10%) • Programmable FET SOA Protection • Programable UV, OV, tFAULT Thresholds • External FET Temperature Sensing • Failed FET Detection • I2C / SMBus Interfac |
|
|
|
|
Texas Instruments |
Positive High-Voltage Hot Swap and In-Rush Current Controller •1 Wide operating range: 9 V to 80 V • In-rush current limit for safe board insertion into live power sources • Programmable maximum power dissipation in the external pass device • Adjustable current limit • Circuit breaker function for severe overcu |
|
|
|
|
ETC |
M50433 Series / Japanese |
|
|
|
|
Texas Instruments |
Voltage Mode Active Clamp Controller 1 •2 Voltage-Mode Control • Line Feed-Forward PWM Ramp • Internal 105V Rated Start-Up Bias Regulator • Programmable Line Under-Voltage Lockout (UVLO) with Adjustable Hysteresis • Versatile Dual Mode Over-Current Protection • Programmable Volt-Second |
|
|
|
|
Texas Instruments |
Dual-Mode PWM Controller 1 •2 High voltage (100V) start-up regulator • Alternating outputs for double-ended topologies • Current-mode or feed-forward voltage-mode control • Programmable maximum duty cycle lLimit • 2% feedback reference accuracy • High gain-bandwidth error am |
|
|
|
|
Texas Instruments |
100-V Push-Pull Voltage Mode PWM Controller •1 Internal High-Voltage (100 V) Start-Up Regulator • Single Resistor Oscillator Setting • Synchronizable • Precision Reference Output • Adjustable Soft Start • Overcurrent Protection • Direct Optocoupler Interface • 1.5-A Peak Gate Drivers • Thermal |
|
|
|
|
Texas Instruments |
Cascaded PWM Controller 1 •2 Internal Start-up Bias Regulator • Programmable Line Under-Voltage Lockout (UVLO) with Adjustable Hysteresis • Current Mode Control • Internal Error Amplifier with Reference • Cycle-by-cycle Over-Current Protection • Leading Edge Blanking • Prog |
|
|
|
|
Texas Instruments |
PWM Controller •1 Internal Start-Up Bias Regulator • 3-A Compound Main Gate Driver • Programmable Line Undervoltage Lockout (UVLO) With Adjustable Hysteresis • Voltage Mode Control With Feed-Forward • Adjustable Dual-Mode Overcurrent Protection • Programmable Overl |
|
|
|
|
Texas Instruments |
PWM Controller •1 Qualified for Automotive Applications • AEC-Q100 Qualified With the Following Results: – Device Temperature Grade 1: –40°C to 125°C Ambient Operating Temperature Range – Device HBM Classification Level 2: ±2 kV – Device CDM Classification Level C4 |
|
|
|
|
Texas Instruments |
Buck Switching Regulator •1 Operating Input Voltage Range: 6 V to 95 V • Integrated 100-V, N-Channel Buck Switch • Internal Start-Up Regulator • No Loop Compensation Required • Ultra-Fast Transient Response • ON Time Varies Inversely With Input Voltage • Operating Frequency |
|