DataSheet.in

UP6101 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - 5V/12V Synchronous-Rectified Buck Controller - uPI Semiconductor

भाग संख्या UP6101
समारोह 5V/12V Synchronous-Rectified Buck Controller
मैन्युफैक्चरर्स uPI Semiconductor 
लोगो uPI Semiconductor लोगो 
पूर्व दर्शन
1 Page
		
<?=UP6101?> डेटा पत्रक पीडीएफ

UP6101 pdf
uP6101
Functional Pin Description
No. Pin Name Pin Function
Bootstrap Supply for the floating upper gate driver. Connect the bootstrap capacitor CBOOT
1
BOOT
between BOOT pin and the PHASE pin to form a bootstrap circuit. The bootstrap capacitor
provides the charge to turn on the upper MOSFET. Typical values for CBOOT range from 0.1uF to
0.47uF. Ensure that CBOOT is placed near the IC.
Upper Gate Driver Output. Connect this pin to the gate of upper MOSFET. This pin is monitored
2 UGATE by the adaptive shoot-through protection circuitry to determine when the upper MOSFET has
turned off.
3
GND
Signal and Power Ground for the IC. All voltages levels are measured with respect to this pin.
Tie this pin to the ground island/plane through the lowest impedance connection available.
Lower Gate Driver Output. Connect this pin to the gate of lower MOSFET. This pin is monitored
4 LGATE by the adaptive shoot-through protection circuitry to determine when the lower MOSFET has turn
off.
Supply Voltage. This pin provides the bias supply for the uP6101 and the lower gate driver. An
5 VCC internal regulator will supply bias if VCC rises above 6.5V. Connect a well-decoupled 4.5V to
13.2V supply voltage to this pin. Ensure that a decoupling capacitor is placed near the IC.
Feedback Voltage. This pin is the inverting input to the error amplifier. A resistor divider from
6 FB the output to GND is used to set the regulation voltage. Use this pin in combination with the
COMP/EN pin to compensate the voltage control feedback loop of the converter.
Error Amplifier Output. This is the output of the error amplifier (EA) and the non-inverting input
7
COMP/EN
of the PWM comparator. Use this pin in combination with the FB pin to compensate the voltage-
control feedback loop of the converter. Pulling COMP/EN to a level below 0.4V nominal disables
the controller and causes the oscillator to stop, the UGATE and LGATE outputs to be held low.
PHASE Switch Node. Connect this pin to the source of the upper MOSFET and the drain of the
lower MOSFET. This pin is used as the sink for the UGATE driver, and to monitor the voltage
8
PHASE
drop across the lower MOSFET for over current protection. This pin is also monitored by the
adaptive shoot-through protection circuitry to determine when the upper MOSFET has turned off.
A Schottky diode between this pin and ground is recommended to reduce negative transient
voltage which is common in a power supply system.
Exposed Pad
For PSOP-8 package. The exposed pad should be well soldered to PCB for effective heat
conduction. Connect the exposed pad the ground.
uPI Semiconductor Corp., http://www.upi-semi.com
Rev. F01, File Name: uP6101-DS-F0101
2
Free Datasheet http://www.datasheet4u.net/

विन्यास 20 पेज
डाउनलोड[ UP6101 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
UP61015V/12V Synchronous-Rectified Buck ControlleruPI Semiconductor
uPI Semiconductor
uP61035V/12V Synchronous-Rectified Buck ControlleruPI Semiconductor
uPI Semiconductor


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English