DataSheet.in

DS9107 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - iButton Capsule - Maxim Integrated Products

भाग संख्या DS9107
समारोह iButton Capsule
मैन्युफैक्चरर्स Maxim Integrated Products 
लोगो Maxim Integrated Products लोगो 
पूर्व दर्शन
1 Page
		
<?=DS9107?> डेटा पत्रक पीडीएफ

DS9107 pdf
DS9107: iButton Capsule
ABSOLUTE MAXIMUM RATINGS
Temperature Range
-40°C to +140°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is
not implied. Exposure to the absolute maximum rating conditions for extended periods may affect device.
SPECIFICATIONS
PARAMETER
Weight
Physical Dimensions
Torque for Tightening the Plug
Number of Open/Close Cycles
Number of Autoclave Cycles
www.DataSheet4U.com
Thermal Response Time
Constant
Empty
CONDITIONS
(Note 1)
Maximum torque applied
From 25°C @ 101.3kPa (14.7psia) to
121°C @ 205kPa (29.7psia), tightened
to maximum torque (Note 2)
(Note 3)
MIN TYP MAX
18.4
See technical drawing
36.5
500
100
UNITS
grams
mm
Nm
150 s
Note 1:
Note 2:
Note 3:
Equivalent to 2.5ft/lbs.
Absolute pressure is specified; the autoclave peak pressure is 103.4 kPa (15 psig) above the standard
atmospheric pressure.
The value was derived from submerging an iButton capsule with DS1922T inside into 55°C water. The
initial temperature of iButton and capsule was 23.5°C. Without capsule, the response time constant is
approximately 30s. Do not drop an unprotected iButton into water or any other liquid.
Top, Plug, Base
Material: Polyphenylene sulfide (PPS Ryton) with black flat finish, electrically non-conductive.
The injection molding compounds (Ryton® PPS) used in the DS9107 are subject to the general safety provisions of
the U.S. Food, Drug and Cosmetic Act. It is the responsibility of the purchaser/user of the DS9107 iButton Capsule
to determine the safety and suitability of the injection molding compounds for their specific application.
O-Ring
Material: S500-70 Silicone Compound, orange, FDA approved.
Replacement O-Rings: Size AS568-019, inner diameter 13/16 inch, outer diameter 15/16 inch, cross section 1/16
inch, nominal values.
Screws
Material: Type 303 austenitic stainless-steel.
Replacement Screws: flat-head Phillips countersunk, self-tapping, M2.3, 9mm long.
APPLICATIONS INFORMATION
The iButton is inserted into the base part with the data contact towards the bottom of the base. The plug is then
placed into the base and initially tightened by hand. Then the base is held with a wrench, and using a metal stick
inserted horizontally into the notch of the plug, the plug is tightened until its head touches the top of the base. It is
important not to exceed the maximum permissible torque.
The iButton Capsule does not provide electrical contact to the iButton inside. Therefore it is necessary to setup
(mission) the temperature logger first before inserting it into the iButton Capsule. To download the logged
temperature data, the logger needs to be taken out of the iButton Capsule.
Ryton is a registered trademark of Chevron Phillips Chemical Company LP.
2 of 3

विन्यास 3 पेज
डाउनलोड[ DS9107 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
DS9100Touch and Hold Probe StampingsDallas Semiconducotr
Dallas Semiconducotr
DS9101Multipurpose ClipMaxim Integrated
Maxim Integrated


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English