DataSheet.in

MAAPSS0096 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - 1 Watt Power Amplifier - Tyco Electronics

भाग संख्या MAAPSS0096
समारोह 1 Watt Power Amplifier
मैन्युफैक्चरर्स Tyco Electronics 
लोगो Tyco Electronics लोगो 
पूर्व दर्शन
1 Page
		
<?=MAAPSS0096?> डेटा पत्रक पीडीएफ

MAAPSS0096 pdf
1 Watt Power Amplifier
4.9 - 6.0 GHz
RoHS
Compliant
MAAPSS0096
V1
Electrical Specifications: TC = 40 °C, VDD = 7.0 V, VGG = -1.8 V, Z0 = 50
Parameter
Test Conditions
Units
Min.
Typ.
Max.
Input VSWR
F = 5.825 GHz, PIN = +14 dBm
1.5:1
2.0:1
Gain
F = 5.825 GHz, PIN = 0 dBm
dB
18.0
20.5
P1dB
F = 5.825 GHz
dBm
29.5
Saturated Power
F = 5.825 GHz, PIN = +14 dBm
dBm
29.2
31.5
Drain Current at Psat
2nd Harmonics
3rd Harmonics
Thermal resistance 3
F = 5.825 GHz, PIN = +14 dBm
Output Power = 29.5 dBm
2nd Stage Only
mA — 500 600
dBc — -40 —
dBc — -70 —
°C/W
31 —
Third-Order Intercept Point
Stability
Noise Figure
+3 V < VDD < +10 V, PIN< +14 dBm, VSWR < 6:1,
-25 ºC < TC < 85 ºC, RBW = 3 MHz (max. hold)
F = 5.825 GHz
dBm
dB
— 40
All spurs < -70 dBc
— 5.3
3. When using the thermal resistance, you must use the power dissipated by the second stage only (not the total power dissipated). The
second stage dissipates 80% of the total power.
Recommended Operating Conditions 4,5
Characteristic Symbol Unit Min. Typ. Max.
Drain Voltage VDD V 4.5 7.0 8.0
Gate Voltage 5 VGG V -2.5 -1.8 -1.0
Input Power
PIN dBm
— 15
Gate Current
IGG mA -4
1 +4
Case Temperature TC
°C -40 25
85
4. Operation outside of these ranges may reduce product
reliability.
5. A 100-ohm resistor should be used in the gate voltage line.
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Absolute Maximum Ratings 6,7
Parameter
Input Power (4.9 - 6.0 GHz)
Operating Voltages
Operating Temperature
Channel Temperature
Storage Temperature
Absolute Maximum
+ 15 dBm
+10 volts
-40 °C to +70 °C
+150 °C
-40 °C to +150 °C
6. Exceeding any one or combination of these limits may cause
permanent damage to this device.
7. M/A-COM does not recommend sustained operation near
these survivability limits.
Operating The MAAPSS0096
To operate the device, follow these steps.
1. Apply VGG = -1.8 V, VDD= 0 V.
2. Ramp VDD to desired voltage, typically 5 to 7 V.
3. Adjust VGG to set IDQ, (approximately –1.8 V).
4. Set RF input.
5. Power down in reverse sequence . Turn gate voltage
off last.
2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
North America Tel: 800.366.2266 / Fax: 978.366.2266
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.

विन्यास 6 पेज
डाउनलोड[ MAAPSS0096 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
MAAPSS0093RF Power Amplifier ICTyco Electronics
Tyco Electronics
MAAPSS0095RF Power AmplifierTyco Electronics
Tyco Electronics


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English