DataSheet.in

AL5814Q डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - AUTOMOTIVE COMPLIANT 60V LINEAR DIMMABLE LED CONTROLLER - Diodes

भाग संख्या AL5814Q
समारोह AUTOMOTIVE COMPLIANT 60V LINEAR DIMMABLE LED CONTROLLER
मैन्युफैक्चरर्स Diodes 
लोगो Diodes लोगो 
पूर्व दर्शन
1 Page
		
<?=AL5814Q?> डेटा पत्रक पीडीएफ

AL5814Q pdf
Typical Application Circuit
VIN
VIN
R5
C1
R6
AL5814Q
VCC
VFAULT
REF
OUT
VSET
GND
SFAULT
FB
R4
D1
R2 Q1
R3
R1
R5
C1
R6
Figure 1
AL5814Q
AL5814Q
VCC
VFAULT
REF
OUT
VSET
SFAULT
GND
FB
R4
D1
R2 Q1
R3
R1
Pin Descriptions
Pin Number
1
Pin Name
VCC
2 REF
3 VSET
4 GND
5 FB
6 SFAULT
7 OUT
8 VFAULT
EP EP
Function
Supply input
Internal reference voltage.
The maximum recommended output current is 50µA and the maximum recommended capacitor
connected from REF pin to GND is less than 100pF.
A potential divider from REF to VSET can be used to accurately set the output LED current.
LED current setting threshold.
The voltage on VSET sets the reference voltage for the FB pin. This pin is pulled down internally if left
floating. The capacitance if needed between VSET and GND is recommended to be less than 1nF.
Ground
Feedback input.
When control loop is operating in linear mode, the FB pin will be regulated to the level set by VSET. This
pin is pulled up internally if left floating.
A capacitor may be added between FB and GND to improve noise rejection. Value needs to be limited to
100pF or less.
VCC enable level setting for LED-open protection activation.
Used in conjunction with VCC to determine
1. If LED-open is activated and
2. At what VCC voltage it becomes active
This function prevents false triggering on power up.
Driving output
For 15mA drive current, VCC must be at least 3V greater than VOUT
Input for LED-open detection.
When LED-open detection function is active, if VFAULT is brought lower than approximately 2.5V, the
device output will be turned off and will auto-retry driving the output to see if the fault still exists.
A PWM dimming function will be realized by adding an open collector/drain signal on this pin.
Exposed Pad (Bottom).
Recommended to be connected to a large-area contiguous copper GND plane for effective thermal
dissipation. Do not use as the IC’s only electrical GND connection.
AL5814Q
Document number: DS41792 Rev. 1 - 2
2 of 14
www.diodes.com
April 2019
© Diodes Incorporated

विन्यास 14 पेज
डाउनलोड[ AL5814Q Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
AL581460V LINEAR DIMMABLE LED CONTROLLERDiodes
Diodes
AL5814QAUTOMOTIVE COMPLIANT 60V LINEAR DIMMABLE LED CONTROLLERDiodes
Diodes


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English