DataSheet.in

GL5171 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - 1.5A 280kHz DC-DC CONVERTOR BOOST REGULATOR - Gleam

भाग संख्या GL5171
समारोह 1.5A 280kHz DC-DC CONVERTOR BOOST REGULATOR
मैन्युफैक्चरर्स Gleam 
लोगो Gleam लोगो 
पूर्व दर्शन
1 Page
		
<?=GL5171?> डेटा पत्रक पीडीएफ

GL5171 pdf
Power Management
Gleam
GL5171
1.5A 280kHz DC-DC CONVERTOR BOPoOwSeTr MRaEnGagUeLmAenTtOR
MARKING INFORMATION & PIN CONFIGURATIONS (TOP VIEW)
SOP-8
PGND
VSW
AGND
VCC
8765
GL5171
AYYWW
12 34
VC SS
FB Test
A = Assembly Location
YY = Year
W W = Work Week
ORDERING INFORMATION (Green Package Products are available now!)
Ordering Number
Package
Shipping
GL5171S8T
GL5171S8R
SOP - 8
SOP - 8
100 Units / Tube
2,500 Units / Tape & Reel
* For detail ordering number identification, please see last page.
PIN DESCRIPTION
PIN NUMBER
1
2
3
4
5
PIN SYMBOL
VC
FB
Test
SS
VCC
FUNCTION
Loop compensation pin. The VC pin is the output of the error amplifier and is used for
loop compensation, current limit and start. Loop compensation can be implemented
by a simple RC network as shown in the application diagram on page 2 as R1 and C1.
Positive regulator feedback pin. This pin senses a positive output voltage and is
referenced to 1.276V. When the voltage at this pin falls below 0.4 V, chip switching
frequency reduces to 20% of the nominal frequency.
These pins are connected to internal test logic and should either be left floating or tied to
ground. Connection to a voltage between 9.5V and 15V shuts down the internal oscillator
and leaves the power switch running.
Synchronization and shutdown pin. This pin may be used to synchronize the part to
nearly twice the base frequency. A TTL low shut the part down and put it into low current
mode. If synchronization is not used, this pin should be either tied high or left floating for
normal operation.
Input power supply pin. This pin supplies power to the part and should have a bypass
capacitor connected to AGND.
Analog ground. This pin provides a clean ground for the controller circuitry ans should
6
AGND
not be in the path of large currents. The output voltage sensing resistors should be
connected to the IC substrate.
7
PGND
Power ground. This pin is the ground connection for the emitter of the power switching
transistor. Connection to a good ground plane is essential.
High current switch pin. This pin connects internally to the collector of the power switch.
8
VSW
The open voltage across the power switch can be as high as 40V. To minimize radiation,
use a trace as short as practical.
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Package Thermal Resistance
Junction-to-Case, RqJC
junction-to-Ambient, RqJC
Junction Temperature Range, TJ
Storage Temperature Range, TSTG
Lead temperature (Peak) (re-flow - soldering
60 sec. Maximum above 183°C)
2 ESD, Human Body Model
VALUE
45
165
-40 to +150
-65 to +150
230
1.2
* The maximum package power dissipation must be observed.
UNITS
°C/ W
°C/ W
°C
°C
°C
kV

विन्यास 18 पेज
डाउनलोड[ GL5171 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
GL51711.5A 280kHz DC-DC CONVERTOR BOOST REGULATORGleam
Gleam


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English